Toshiba Tosvert VF-AS1 Bedienungsanleitung Seite 123
- Seite / 312
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
E6581301
F-11
6
6.5 V/f 5-point setting
H :
V/f 5-point setting VF1 frequency
H :
V/f 5-point setting VF1 voltage
H :
V/f 5-point setting VF2 frequency
H :
V/f 5-point setting VF2 voltage
H :
V/f 5-point setting VF3 frequency
H :
V/f 5-point setting VF3 voltage
H :
V/f 5-point setting VF4 frequency
H :
V/f 5-point setting VF4 voltage
H :
V/f 5-point setting VF5 frequency
H :
V/f 5-point setting VF5 voltage
⇒ For details, refer to Section 5.6,5).
6.6 Speed/torque command gain and bias
6.6.1 Using two types of frequency (speed) commands
HOQF : Frequency setting mode selection 1
H
: Frequency priority selection
H
: Frequency setting mode selection 2
H
: Speed command priority switching frequency
• Function
These parameters switch two types of frequencies
• Automatic switching by parameter setting
• Automatic switching by means of switching frequencies
• Switching with input terminal
1) Switching with input terminal board (H=)
Reference can be switched if the frequency priority switching function is assigned to a terminal.
Command selected
with HOQF
Command selected
with H
Operation frequency
command
A
B
A : Selects the command set with parameter HOQF. – Operation frequency command switching terminal OFF
B : Selects the command set with parameter H. – Operation frequency command switching terminal ON
Ex.) When the frequency priority switching function is assigned to terminal S3.
Title Function Adjustment range Example of setting
H Input terminal function selection 7 (S3) ~
(Operation frequency command
switching)
Speed command
OFF
Command selected with
HOQF
ON
Command selected with
H
S3
CC
- E6581301Ԙ 1
- I. Safety precautions 3
- Danger 4
- II. Introduction 9
- E6581301 11
- - Contents 11
- 1. Read first 17
- 1.3.1 Names and functions 18
- 1) Outside view 18
- 1.3.2 Detaching the cover 25
- 1.4 Notes on the application 30
- 1.4.1 Motors 30
- 1.4.2 Inverters 32
- ■ Disposal 32
- Warning 33
- 1.4.4 Installation 35
- ■ Installation environment 35
- ■ How to install 36
- 2. Connection equipment 41
- 2.2 Standard connections 43
- 2.3 Description of terminals 48
- 3. Operations 55
- Status monitor mode 56
- Standard monitor mode 56
- (when the power is turned on) 56
- Setting monitor mode 56
- Deceleration 57
- 3.2.2 Panel operation 61
- 4.1 How to set parameters 64
- 5. Basic parameters 67
- CW : Automatic torque boost 69
- ■ Preset speed operation 74
- + The inverter is factory 75
- +To save the frequency 75
- HE and the set 75
- 5.6 Selecting control mode 77
- 2) Decreasing output voltage 78
- 3) Increasing starting torque 78
- 5.8 Base frequency 81
- 5.9 Maximum frequency 82
- Estimation of temperature 90
- 5.17 PWM carrier frequency 96
- Warning 97
- Surge killer 103
- 5.20 Standard default setting 107
- ( ) 109
- 5.22 EASY key function 110
- 6. Extended parameters 113
- 6.2 Input signal selection 115
- Internal command 116
- Servo lock status 120
- Command selected 123
- Operation frequency 125
- 6.8 DC braking 126
- 6.10 Jog run mode 131
- Jumping width 2 135
- Jumping width 1 135
- 6.14.1 Retry function 136
- 6.15 Drooping control 139
- Load portion torque input 141
- 6.20 PID control 145
- 6.22 Setting motor constants 148
- Setting motor constants 150
- 6.24 Torque control 152
- 6.25 Torque limit 154
- Positive torque 155
- Negative torque 155
- • Function 158
- 6.31 Pattern operation 163
- 6.32 Preset speed mode 165
- 6.33 Protection functions 166
- 6.33.3 Emergency stop 167
- H : Emergency stop 167
- 6.34 Override 175
- 6.35 Adjustment parameters 177
- Function 179
- ■ Example of setting 1 181
- ■ Example of setting 2 181
- 6.37 Tracing functions 183
- Trace data 1 184
- Trigger input 184
- 6.38 Communication function 187
- 1) 2-wire RS485 188
- 2) 4-wire RS485 190
- Host computer 191
- 6.39 My function 193
- 6.40 Traverse function 194
- 7.1 External operation 195
- B-contact switch 196
- Input terminal 196
- Inverter 196
- Programmable controller 197
- 7.2.4 Analog input filter 203
- 8.2 Monitoring the status 210
- 8.4.1 Trip code display 216
- 9.1.1 EMC directive 221
- Contact your supplier 222
- Use the 224
- EMC FILTER 226
- Ferrite core 1 227
- Shielded cable or [Note 1] 227
- Noise cut plate 228
- AIC, Fuse and Wire sizes 229
- Ｅ６５８１３００ 232
- Note on wiring 233
- 11. Table of parameters 239
- 12. Specifications 285
- E6581301 286
- ■ Outside dimensions and mass 289
- (Installation dimension) 290
- Before making a service call 295
- Cautions about cleaning 303
- 14.2 Periodical inspection 304
- ■ Check items 304
- 15. Warranty 307
- Warning 309
Verwandte Produkte und Handbücher für Werkzeug Toshiba Tosvert VF-AS1
Werkzeug Toshiba HX7 Bedienungsanleitung
(6 Seiten)
(6 Seiten)
Werkzeug Toshiba 1500 Plus Bedienungsanleitung
(31 Seiten)
(31 Seiten)
Werkzeug Toshiba G8000 Bedienungsanleitung
(79 Seiten)
(79 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.052 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern