Toshiba IK-DP30A Bedienerhandbuch

INSTRUCTION MANUALDOME CAMERAIK-DP30ATABLE OF CONTENTSIMPORTANT SAFEGUARDS ... 21. Features and descripti

- 10 -FRAME SCANThe dome camera can perform a frame scan operation during power-up and by direct control fromthe keyboard.Operation of zoom and tilt i

- 11 -RANDOM SCANThe dome camera can perform a random scan operation during power-up and by direct controlfrom the keyboard.Operation of zoom and tilt

- 12 -6.7 CAMERA SETUP6.7.1 FOCUS CONTROLDirect• The focus can be controlled directly using near or far focusing controls.• The focus control has 4 va

- 13 -6.7.2 WHITE BALANCE CONTROLDirect• The White Balance can be set by One Push Trigger operation.Menu<CAMERA SETUP><PAN/TILT SETUP><

- 14 -MODE• AE mode can be set to FULL AUTO or SHUTTER PRIORITY.• FULL AUTO mode:The shutter is fixed at 1/60 sec and the camera will automatically ad

- 15 -To change the AE options:1. Enter the preset command to access the main menu.Refer to section 6.1 for the controller model and preset command.2

- 16 -6.7.5 SHARPNESSMenu<CAMERA SETUP><PAN/TILT SETUP><PRESET TITLES><OTHERS>EXITMAIN MENU<FOCUS>WB ATW<AE>ZO

- 17 -To change the LINE LOCK options:1. Enter the preset command to access the main menu.Refer to section 6.1 for the controller model and preset co

- 18 -Notes:1) Masking areas are only rectangles.2) When using the PTZ function the privacy zone expands 2x vertically and 4x horizontally.3) Although

- 19 -6.8.2 PROPORTIONAL P/TProportional P/T controls the pan and tilt speeds according to the amount of zoom.At telephoto settings, the pan and tilt

- 2 -1. Read InstructionsAll the safety and operating instructions should beread before the product is operated.2. Retain InstructionsThe safety instr

- 20 -To enable SCAN LIMIT STOPS:1. Enter the preset command to access the main menu.Refer to section 6.1 for the controller model and preset command

- 21 -4. Position the camera for the RIGHT LIMIT STOP. If the right limit stop is less than 10 degreesfrom the left limit stop, NOT ACCEPT will be dis

- 22 -To enable AUTO PATROL:1. Enter the preset command to access the main menu.Refer to section 6.1 for the controller model and preset command.2. P

- 23 -6.8.8 SCAN TILT ANGLEThe tilt angle of the dome camera for auto scan, random scan and frame scan can be set from 0 to85 degrees or 92 degrees (0

- 24 -To set STOP TIME:1. Enter the preset command to access the main menu.Refer to section 6.1 for the controller model and preset command.2. Positi

- 25 -6.9 PRESET TITLES SETUPTitles can be set for up to 64 presets (pan/tilt position and zoom). Titles can be up to 20 charactersin length and can b

- 26 -6.10 OTHERS MENU6.10.1 POWER UPDuring Power-Up, the dome camera can be set to start in various modes.PARK: The dome camera moves to Preset 1 pos

- 27 -6.10.2 FREEZE ACTIVITYDuring frame scan, random scan or auto patrol, camera images will not be shown while the domecamera moves from the current

- 28 -6.10.4 TILT ANGLESet up the Tilt angle according to the housing used and the purpose.Indoor - 85 degrees MAXOutdoor - 92 degrees MAXMenuMAIN MEN

- 29 -7. Menu Directory<CAMERA SETUP><PAN/TILT SETUP><PRESET TITLES><OTHERS>EXITTOP MENU<FOCUS>WB ATW<AE>ZOOM

- 3 -• The CAUTION label, shown on the left,is attached on the camera.CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK.DO NOT REMOVE COVER (OR BACK).NO US

- 30 -7.1 MENU LIST AND SETTINGSTop MenuSub Menu 1 Sub Menu 2ContentsDefaultCAMERASETUPFOCUSWHITE BALANCEAUTO EXPOSURE- - - -AUTO / MANUAL / ZOOMTRIGG

- 31 -8. Switch SettingThere are three switches which must be set up. Switch 1 sets the camera address. Switch 2 setsthe protocol and bit rate. Switch

- 32 -(1) SWI : Camera Addressbit1OnOffOnOffOnOffOnOffOnOffOnOffOnOffOnOffOnOffOnOffOnOffOnOffOnOffOnOffOnOffOnOffOnOffOnOffOnOffOnOffOnOffOnOffOnOffO

- 33 -Camera Address = 1 × bit 1 Status + 2 x bit 2 Status + 4 × bit 3 Status + 8 × bit 4Status + 16 × bit 5 Status +32 × bit 6 Status + 64 × bit 7Sta

- 34 -9. InstallationJK-H01A is a housing for ceiling mount of the Toshiba dome camera.1. IK-DP30A Installation procedure (1) Carefully inspect to ins

- 35 -(JK-H01A top housing install) (6) Move the two support arms inside. Fig-2 (7) Remove knockout in the center of the housingand let the cable pass

- 36 -(IK-DP30A dome base install)(11) Attach the video cable (included with the domeaccessories) to the video connector of a domebase. [Note: Do not

- 37 -10. SpecificationsOverallTemperature of operation 32° to 122°F (0° to 50°C)Preservation temperature –4° to 140°F (–20° to 60°C)Weight 1.8 kgPowe

- 38 -MechanicalPan Range 360 degrees continuousTilt Range 92 degrees (Outdoor)Manual Pan Speeds 0.1° - 90°/sManual Pan Speeds (turbo) 150°/sManual Ti

- 4 -1. Features and descriptionQuick Install Design - Cuts Installation Time in Half480 Lines Horizontal Resolution400 Degree/Second Pan18X Optical/1

LIMITED WARRANTYCCD SECURITY DOME CAMERA IK-DP30AThe Imaging System Division (“ISD”) of Toshiba America Information Systems, Inc makes the following l

- 5 -4. Part names and Locations120120°° 120120°° 3535°° φφ134134173.7173.7223.7223.7R19R19R1.9Φ139.8Control Terminal (RS-422)Installation NotchIn

- 6 -5. ConnectionsBasic connection (Direct mode)24V AC UL Iisted class 2 power supplyRS422(twisted pair line)MonitorKeyboardAC AdaptorMake sure to co

- 7 -6. Operation(Power On display)When the dome camera powers-up, the software version,selected protocol, and other information are displayed on them

- 8 -6.2 Preset CommandsThe dome camera can set and perform various preset commands. The following table lists thepreset number and whether is can be

- 9 -Pan Range 360 degrees continuousTilt Range 85 degrees (Indoor), 92 degrees (Outdoor)Manual Pan Speeds 0.1° – 90°/sManual Pan Speeds (turbo) 150°/